Fixed Stations

When you create a new fixed Station, the dialog shown below will appear.

Fixed Terrestrial Station Dialog
Fixed Station Dialog

The Station icon can be changed by clicking on the small black arrow by the side of the icon. This produces a drop-down menu from which a new icon can be selected.

Station Icon Selection
Station Icon Selection

The tabs shown when this station is created are Position, Traffic and Advanced.

Position

The position tab allows you to set the location of the Station.

You can change the latitude and longitude of the Station. Clicking on the units will produce a popup menu from which you can pick the units that are appropriate.

Station Units Selection
Station Units Selection

If you select degrees, minutes, seconds, the format is:

[N/S/E/W] DD:MM’SS.SS”

You can choose whether to specify the height of your Station above the terrain or above sea level. If you have any terrain data in this simulation the terrain height at that location is displayed.

Adding and Managing Antennas

A Station can have multiple Antennas. The parameters for each Antenna are presented on a separate tab. By default, a Station is created with one Antenna.

An example Antenna tab is shown below.

Antenna Tab
Antenna Tab

The parameters for the selected Antenna are:

  • Type – which of your library of antenna models to use for this station
  • Feeder loss – what is the loss in dB due to the feed from the antenna to the receiver (not transmitter – see Technical Annex for more information)
  • Pointing options – how is the pointing of this antenna determined.

Click the Select button to change the type of Antenna. This will show a dialog from which you can choose one of the new Antennas you have created.

Choose Antenna Dialog
Choose Antenna Dialog

Choosing an Antenna Type means that the Station will use the characteristics of the Antenna as defined in the Antenna list. An important point is that if the Antenna in the Antenna list changes, all Stations that use that Antenna will change accordingly.

Antenna Pointing

They presented as a set of radio buttons and the options are described in Antenna and Beam Pointing. Clicking the required method reveals the parameters needed to fully define it.

First you decide how you want to point your Antenna, and then you set the required parameters for the pointing option you have chosen.

More options

The ‘more options’ button allows you to specify Antenna temperature and the Antenna height.

Feeder temperature is needed if you are going to let Visualyse Interplanetary calculate system noise from the component contributions due to the Antenna, feeder and receiver. The choice of how to calculate system noise is made in the Link dialog – you have the option simply to enter the system noise directly in Kelvins, and if you are going to do this there is no need to enter the Antenna noise.

Antenna height is the height above the Station, and has some influence on some propagation models and, of course some influence on the simulation geometry.

Antenna Options
Antenna Options

Managing Multiple Antennas in a Single Station

Management of multiple antennas is very similar to that of beams on the Antenna dialog (Managing Beams). To add multiple Antennas, click on the black arrow to the right of the Add Antennas button.

Adding Antennas
Adding Antennas

From this menu, you can choose how many Antennas you want to add to your Station. There are options for quickly adding up to four Antennas at a time. If you want more than four Antennas, click the More Antennas option. A dialog box will appear allowing you to specify the exact number of Antennas you require.

More Antennas
More Antennas

New Antennas appear as new tabs. If there are more Antennas than will fit across the dialog, scroll buttons will appear to allow you to access the extra tabs.

Duplicating and deleting functions work on the currently selected Antenna. If you duplicate, the new Antenna becomes the active selection. If you delete, the next Antenna becomes the selection (unless you delete the last Antenna in which case the previous Antenna becomes the active selection)

Naming Antennas

Antennas are automatically given names by the software. However, you can give your Antennas more meaningful names, and this practise is encouraged because good naming makes complex models easier to understand (especially if you revisit them at some time in the future and need to remember what you were doing)

You rename the antenna by interacting with the name on the tab directly. It works in the same way as when you change the Station name.

When the mouse passes over the Antenna name the cursor changes to a caret,

If you click on the name, it changes to an edit box so that you can alter it. This is shown below.

Antenna Name Edit

Typing a new name causes the tab to automatically resize. Click away or hit Return to finish editing.

Antenna Name Edit Resize

You can only do this with the selected Antenna. To change the name of another Antenna, you need to select it first.

Advanced Option

The advanced tab incorporates the Station coordinate system parameters and attitude parameters relating to the station reference frame.

Advanced Station Options
Advanced Station Options

For a description of the effect of changing the coordinate system reference, and for definitions of the Station azimuth and elevation see the Technical Annex.

Traffic Modelling

Traffic won’t appear on the Station dialog at all unless your installation has the traffic module. If traffic is enabled, the traffic tab will appear as shown below.

Traffic Tab
Traffic Tab

For details of how to use the traffic module, please refer to the Module User Guide. Note the maximum load field can be used by the Population Data processing as described in Service Area Wizard.